Miracle Shield
Miracle Shield is a revolutionary coating that adds luster
without the use of silicones or waxes. Miracle Shield dries
crystal clear without any buffing, and protects without leaving
a greasy or oily feel like the other nationally advertised
"protective coatings".
Cleans, protects and beautifies: vinyl, leather, wood, plastics,
carpets, chairs, autos, trucks, TV's, boats, rubber, and most
painted surfaces.
It even protects against mildew growth, graffiti and wear on
virtually all non-cloth surfaces.
It's guaranteed never to chip, crack or peel and will never
yellow. It is non-flammable and non-toxic and contains no
harmful oils or waxes.
without the use of silicones or waxes. Miracle Shield dries
crystal clear without any buffing, and protects without leaving
a greasy or oily feel like the other nationally advertised
"protective coatings".
Cleans, protects and beautifies: vinyl, leather, wood, plastics,
carpets, chairs, autos, trucks, TV's, boats, rubber, and most
painted surfaces.
It even protects against mildew growth, graffiti and wear on
virtually all non-cloth surfaces.
It's guaranteed never to chip, crack or peel and will never
yellow. It is non-flammable and non-toxic and contains no
harmful oils or waxes.
Surfaces
Use Miracle Shield on the following surfaces:
Vinyl
Plastic
Rubber
Metal
Interior Wood
Roof's
Concrete
Asphalt
Stone Work
Brick Work
NOTE: Outdoor applications should be a minimum of two coats solution.
Finish- Miracle Shield will dry to a satin or low-luster semi-gloss finish. Which is scratch resistant. There
is no buffing required.
Application- Miracle Shield can be applied as follows:
Brush it on
Spray it on
Roll it on with a short nap roller
Wipe it on
Sponge it on
Miracle Shield hardens best at a surface temperature of 55 degrees or higher on an average of 15-20
minutes.
Surface Preparation- In order for Miracle Shield to work properly, the surface must be free from any
dust, dirt grease, grime or wax. You can remove any oil, wax or grease with household rubbing alcohol.
Use Miracle Shield on the following surfaces:
Vinyl
Plastic
Rubber
Metal
Interior Wood
Roof's
Concrete
Asphalt
Stone Work
Brick Work
NOTE: Outdoor applications should be a minimum of two coats solution.
Finish- Miracle Shield will dry to a satin or low-luster semi-gloss finish. Which is scratch resistant. There
is no buffing required.
Application- Miracle Shield can be applied as follows:
Brush it on
Spray it on
Roll it on with a short nap roller
Wipe it on
Sponge it on
Miracle Shield hardens best at a surface temperature of 55 degrees or higher on an average of 15-20
minutes.
Surface Preparation- In order for Miracle Shield to work properly, the surface must be free from any
dust, dirt grease, grime or wax. You can remove any oil, wax or grease with household rubbing alcohol.
Cleaning Properties-Miracle Shield has no known cleaning properties such as some other multi-purpose
sealants. However, some applications have shown that mild mars, rust and stains have been removed when
applied.
Viscosity- The thickness of Miracle Shield is determined by it's application. The standard application is
either by brush, spraying or rolling. With standard applications, about 2 mil. of product is realized per coat.
Product Indications/Preparation- Miracle Shield comes already mixed and ready for use right out of the
container. There is no mixing or dilution necessary.
No mixing
No diluting
No concentrates to bother with
Water Soluble
Ready to use
Cleans with soap and water when wet
Cleans with alcohol when dry
Restrictions- Miracle Shield is not to be used on glass, mirrors, chrome or brass.
Hazards- Miracle Shield is a mixture of 55% water and 45% chemical solvent.
Combustible fumes are emitted in it's wet state
Perfectly safe in it's dry state
When applying, ventilate area of application well
Keep container closed when not in use
Protects Against:
Mildew/Moisture/Water
Graffiti
Grease/Grime/Oil
Wear on non-cloth surfaces
sealants. However, some applications have shown that mild mars, rust and stains have been removed when
applied.
Viscosity- The thickness of Miracle Shield is determined by it's application. The standard application is
either by brush, spraying or rolling. With standard applications, about 2 mil. of product is realized per coat.
Product Indications/Preparation- Miracle Shield comes already mixed and ready for use right out of the
container. There is no mixing or dilution necessary.
No mixing
No diluting
No concentrates to bother with
Water Soluble
Ready to use
Cleans with soap and water when wet
Cleans with alcohol when dry
Restrictions- Miracle Shield is not to be used on glass, mirrors, chrome or brass.
Hazards- Miracle Shield is a mixture of 55% water and 45% chemical solvent.
Combustible fumes are emitted in it's wet state
Perfectly safe in it's dry state
When applying, ventilate area of application well
Keep container closed when not in use
Protects Against:
Mildew/Moisture/Water
Graffiti
Grease/Grime/Oil
Wear on non-cloth surfaces
Additional Info on Miracle Shield
Elastomeric Clear Sealer, Finish
Miracle Shield is a Clear Acrylic Elastomeric Sealant designed to seal and protect a wide range of
surfaces including wood homes, stone, brick, masonry and concrete, roofing materials and reflective roof
coatings.
All white roof coatings start losing their reflectivity properties due to accumulated dirt and other
contaminates. Until now clear protective coatings for elastomeric base coatings were not available due to
their lack of flexibility which is necessary as roof coatings are designed to expand and contract with a roofs
movement.
Miracle Shield also features outstanding adhesion to the applied surface, elongation and recovery
capabilities, a combination of UV absorbers and mildewcides enabling it to resist the effects of the most
severe climatic conditions. Now all roof coatings can be protected from surface contamination enabling
them to perform as intended by reflecting radiant heat away from the buildings interior.
This self cleaning clear coat works much the same way as the clear coatings designed and used on
automobile finishes.
Miracle Shield is truly an all-purpose clear sealant and protectant, suitable for virtually any application.
Color: Milky White, dries clear.
Volume Solids: 41% +/- 2%
Flash Point: Same as water.
Coverage: 350-400 sq. ft. per gallon depending on the porosity of the surface.
Recommended Coverage: The number of coats depends on surface porosity; however, one coat is all that
is normally needed on a well sealed surface.
Drying Time: Will depend on climate conditions. Allow at least 2 hours drying time between coats. First coat
must be thoroughly dry before applying second coat.
Limitations: Not suitable for below grade use.
Surface Preparation Surface must be clean and free from dirt, dust, grease, oil, mildew, wax, loose paint.
Application: This product may be easily applied with a quality brush, short nap roller or airless spray
equipment. Surface must be clean, dry and sound. Surface must be free of grease, oil wax, mildew or any
other surface contaminant. Surface and ambient temperatures should be between 45 and 90 F. Avoid
application if rain or condensation could wet surface less than 1 hour after application. Allow 2 hour
between coats for best results.
If applying by brush, apply a smooth, generous coat in small areas or cut in large areas first. If applying by
roller, apply in even, generous strokes in an “M” or criss-cross pattern avoiding excessive respeading or
reworking. Always maintain a wet edge by brushing or rolling into the previously applied area.
If applying by airless spray equipment, it is recommended to use a unit with a minimum of 2,000 psi
pressure, with a 0.013 to 0.021 fluid spray tip. During application, product should be back-rolled to insure
proper adhesion and even dispersion. Thinning should not be necessary but use a maximum of ½ pint per
gallon if it is. Clean up equipment and any spills immediately with warm soapy water and thoroughly rinse
with clean water.
Clean-up: Cleanup immediately after use with soap and water.
Miracle Shield FAQs
Question: What kinds of surfaces can MS be used on ?
Answer: Wood, Concrete, Plastic, Vinyl, Rubber, Roofing materials … just about anything.
Question: What does MS do ?
Answer: Forms a clear, flexible barrier film. Never slippery or oily. Easy application - just apply & let dry. Will
not crack or peel. Protects against Ultra-Violet damage with no silicones or waxes. Works on most non-
cloth surfaces. Treated surface cleans up with soap and water.
Question: What color is it ?
Answer: MS goes on as a slightly milky, translucent liquid. It dries clear. Tinting has not been tested. Try a
small sample first.
Question: What kind of coverage can I expect ?
Answer: You can figure that the average spread rate is 300 to 500 sqft/gal and highly dependent upon the
porosity of the surface. Concrete pool deck about 300, Cedar yard fencing 400, Stucco wall 250, Old
asbestos shingles 300, Wood patio deck 500, Public restroom dividers 600+ when diluted.
Question: How should it be applied ?
Answer: It can be rolled, brushed or sprayed. In vertical applications, it can even be wiped on with a damp
cloth.
Question: What is the life time of the coating ?
Answer: High traffic areas should have 2 or more coats applied and life will vary from 2 to 5 years. Vertical
applications will last for the lifetime of the surface. A typical roofing application will extend the life of the roof
another 10 years.
Question: Is the surface slippery ?
Answer: NO. MS will have a slight elastic “give” to it’s surface which should give a superior non-slip
characteristic.
Question: Will it resist graffiti ?
Answer: YES ! Surface will clean up with just soap and water. Many users find that diluting 1:1 in a spray
bottle gives the desired result.
Question: Can I spray MS over Therma Guard paint ?
Answer: YES ! These products work exceptionally well together. Ideal applications include a roof or external
walls where you can mate the radiant reflection and insulating properties of TG with the sealing elastic
properties of the MS.
Question: Can I mix TG Cells with MS and get protection and insulation simultaneously ?
Answer: YES ! TG Cells (packaged dry ceramic spheres) are a new product in the Therma Guard line.
Industrial users mix these products with great results and gain the benefits of both products with one
application. This is very popular in roof repair applications.
Question: Does MS contain harmful chemicals ?
Answer: NO. MS is free of all Volatile chemicals and toxins and is recognized as safe, under the Federal
Food, Drug, and Cosmetic Act. Non-toxic, odor free and environmentally friendly.
Question: Can MS be diluted ?
Answer: YES. It just forms a thinner protective coating
Question: Is there a craft application for MS ?
Answer: YES ! Absolutely ! Paintings, ceramics, wood working projects, jewelry ect. Anything where water
proofing, UV and mildew protection would be a benefit. Try it a test surface first to insure a desired result.
Miracle Shield is a Clear Acrylic Elastomeric Sealant designed to seal and protect a wide range of
surfaces including wood homes, stone, brick, masonry and concrete, roofing materials and reflective roof
coatings.
All white roof coatings start losing their reflectivity properties due to accumulated dirt and other
contaminates. Until now clear protective coatings for elastomeric base coatings were not available due to
their lack of flexibility which is necessary as roof coatings are designed to expand and contract with a roofs
movement.
Miracle Shield also features outstanding adhesion to the applied surface, elongation and recovery
capabilities, a combination of UV absorbers and mildewcides enabling it to resist the effects of the most
severe climatic conditions. Now all roof coatings can be protected from surface contamination enabling
them to perform as intended by reflecting radiant heat away from the buildings interior.
This self cleaning clear coat works much the same way as the clear coatings designed and used on
automobile finishes.
Miracle Shield is truly an all-purpose clear sealant and protectant, suitable for virtually any application.
Color: Milky White, dries clear.
Volume Solids: 41% +/- 2%
Flash Point: Same as water.
Coverage: 350-400 sq. ft. per gallon depending on the porosity of the surface.
Recommended Coverage: The number of coats depends on surface porosity; however, one coat is all that
is normally needed on a well sealed surface.
Drying Time: Will depend on climate conditions. Allow at least 2 hours drying time between coats. First coat
must be thoroughly dry before applying second coat.
Limitations: Not suitable for below grade use.
Surface Preparation Surface must be clean and free from dirt, dust, grease, oil, mildew, wax, loose paint.
Application: This product may be easily applied with a quality brush, short nap roller or airless spray
equipment. Surface must be clean, dry and sound. Surface must be free of grease, oil wax, mildew or any
other surface contaminant. Surface and ambient temperatures should be between 45 and 90 F. Avoid
application if rain or condensation could wet surface less than 1 hour after application. Allow 2 hour
between coats for best results.
If applying by brush, apply a smooth, generous coat in small areas or cut in large areas first. If applying by
roller, apply in even, generous strokes in an “M” or criss-cross pattern avoiding excessive respeading or
reworking. Always maintain a wet edge by brushing or rolling into the previously applied area.
If applying by airless spray equipment, it is recommended to use a unit with a minimum of 2,000 psi
pressure, with a 0.013 to 0.021 fluid spray tip. During application, product should be back-rolled to insure
proper adhesion and even dispersion. Thinning should not be necessary but use a maximum of ½ pint per
gallon if it is. Clean up equipment and any spills immediately with warm soapy water and thoroughly rinse
with clean water.
Clean-up: Cleanup immediately after use with soap and water.
Miracle Shield FAQs
Question: What kinds of surfaces can MS be used on ?
Answer: Wood, Concrete, Plastic, Vinyl, Rubber, Roofing materials … just about anything.
Question: What does MS do ?
Answer: Forms a clear, flexible barrier film. Never slippery or oily. Easy application - just apply & let dry. Will
not crack or peel. Protects against Ultra-Violet damage with no silicones or waxes. Works on most non-
cloth surfaces. Treated surface cleans up with soap and water.
Question: What color is it ?
Answer: MS goes on as a slightly milky, translucent liquid. It dries clear. Tinting has not been tested. Try a
small sample first.
Question: What kind of coverage can I expect ?
Answer: You can figure that the average spread rate is 300 to 500 sqft/gal and highly dependent upon the
porosity of the surface. Concrete pool deck about 300, Cedar yard fencing 400, Stucco wall 250, Old
asbestos shingles 300, Wood patio deck 500, Public restroom dividers 600+ when diluted.
Question: How should it be applied ?
Answer: It can be rolled, brushed or sprayed. In vertical applications, it can even be wiped on with a damp
cloth.
Question: What is the life time of the coating ?
Answer: High traffic areas should have 2 or more coats applied and life will vary from 2 to 5 years. Vertical
applications will last for the lifetime of the surface. A typical roofing application will extend the life of the roof
another 10 years.
Question: Is the surface slippery ?
Answer: NO. MS will have a slight elastic “give” to it’s surface which should give a superior non-slip
characteristic.
Question: Will it resist graffiti ?
Answer: YES ! Surface will clean up with just soap and water. Many users find that diluting 1:1 in a spray
bottle gives the desired result.
Question: Can I spray MS over Therma Guard paint ?
Answer: YES ! These products work exceptionally well together. Ideal applications include a roof or external
walls where you can mate the radiant reflection and insulating properties of TG with the sealing elastic
properties of the MS.
Question: Can I mix TG Cells with MS and get protection and insulation simultaneously ?
Answer: YES ! TG Cells (packaged dry ceramic spheres) are a new product in the Therma Guard line.
Industrial users mix these products with great results and gain the benefits of both products with one
application. This is very popular in roof repair applications.
Question: Does MS contain harmful chemicals ?
Answer: NO. MS is free of all Volatile chemicals and toxins and is recognized as safe, under the Federal
Food, Drug, and Cosmetic Act. Non-toxic, odor free and environmentally friendly.
Question: Can MS be diluted ?
Answer: YES. It just forms a thinner protective coating
Question: Is there a craft application for MS ?
Answer: YES ! Absolutely ! Paintings, ceramics, wood working projects, jewelry ect. Anything where water
proofing, UV and mildew protection would be a benefit. Try it a test surface first to insure a desired result.
Miracle Shield 1 Gallon $110